Abstract
The development of an efficient electronic metering system is crucial for the successful deployment of urea super granules (USGs) in agricultural fields. Key parameters influencing the performance of the cell-type metering system for USG application include cell area, peripheral speed of the cell, and the level of hopper filling. Simulation of the metering system operation was conducted using EDEM, with a focus on optimizing input parameters to achieve 100% cell fill, maximum qualified rate for single cells, and minimization of missing or multiple cells. An electronic metering system was implemented in a soil bin, employing a Nema 23 stepper motor to control the peripheral speed of the cell. The synchronization with the transplanter was ensured through a rotary encoder, and various cell sizes were achieved using 3D printing. Using the EDEM-RSM approach, the optimal operating conditions based on the soil bin study were found as cell area of 1088 mm2, a metering roller peripheral speed of 0.24 m/s, and a 75% hopper fill. Under these conditions, the system demonstrated a 97% cell fill, a 91% qualified rate for single cells, with only 3.2% missing cells and 4.5% multiple cells. Quality class of metering was found as good based on indices such as missing index, multiple index, and quality of feed index, which were found as 3.2%, 4.5%, and 92.3%, respectively. The study demonstrated the robust predictive capability of the EDEM-RSM model in evaluating the performance of the cell-type metering system. These findings offer valuable insights for researchers and manufacturers seeking to optimize the development of automated ultrasonic (USG) applicators.
Data availability
The datasets used and/or analysed during the current study are available from the corresponding author on reasonable request.
References
Houghton, J. T. IPCC (intergovernmental panel on climate change). The science of climate change (1986).
Guo, C., Liu, X. & He, X. A global meta-analysis of crop yield and agricultural greenhouse gas emissions under nitrogen fertilizer application. Sci. Total Environ. 831, 154982 (2022).
Liu, T. Q. et al. Advantages of nitrogen fertilizer deep placement in greenhouse gas emissions and net ecosystem economic benefits from no-tillage paddy fields. J. Clean. Prod. 263, 121322 (2020).
Huda, A. et al. Floodwater ammonium, nitrogen use efficiency and rice yields with fertilizer deep placement and alternate wetting and drying under triple rice cropping systems. Nutr. Cycl. Agroecosyst. 104, 53–66 (2016).
Mofijul Islam, S. M. et al. Rice yields and nitrogen use efficiency with different fertilizers and water management under intensive lowland rice cropping systems in Bangladesh. Nutr. Cycl. Agroecosyst. 106, 143–156 (2016).
Chatterjee, D. et al. Agriculture, Ecosystems and Environment Comparative assessment of urea briquette applicators on greenhouse gas emission, nitrogen loss and soil enzymatic activities in tropical lowland rice. Agric. Ecosyst. Environ. 252, 178–190 (2018).
Hossen, M. A. et al. Design and development of a manually operated urea supper granule (USG) applicator. AMA, Agricultural Mechanization in Asia. Afr. Latin Am. 44, 85–91 (2013).
Wohab, M. A., Gaihre, Y. K., Ziauddin, A. T. M. & Hoque, M. A. Design, development and field evaluation of manual-operated applicators for deep placement of fertilizer in puddled rice fields. Agric. Res. 6, 259–266 (2017).
Savant, N. K., Ongkingco, P. S., Zarate, I. V., Torrizo, F. M. & Stangel, P. J. Urea briquette applicator for transplanted rice. Fertil. Res. 28, 323–331 (1991).
Kaur, T. & Kumar, D. Design and development of calibration unit for precision planter. Int. J. Comput. Sci. Eng. Appl. 3, 11 (2013).
Ruicheng, D. et al. Design and experiment on intelligent fuzzy monitoring system for corn planters. Int. J. Agricultural Biol. Eng. 6, 11–18 (2013).
Taghinezhad, J., Alimardani, R. & Jafary, A. Design a capacitive sensor for rapid monitoring of seed rate of sugarcane planter. Agric. Eng. Int.: CIGR J. 15, 23–29 (2013).
Iacomi, C. & Popescu, O. A new concept for seed precision planting. Agric. Agric. Sci. Proc. 6, 38–43 (2015).
Koley, S., Bhatt, Y. C., Singh, G., Joshi, S. & Jain, H. K. Development of electronic metering mechanism for precision planting of seeds. Int. J. Curr. Microbiol. Appl. Sci. 6, 3481–3487 (2017).
Kang, N., Xianfa, F., Yangchun, L., Chengxu, L. & Yanwei, Y. Optimized design and performance evaluation of an electric cup-chain potato metering device. Int. J. Agric. Biol. Eng. 10, 36–43 (2017).
Cay, A., Kocabiyik, H. & May, S. Development of an electro-mechanic control system for seed-metering unit of single seed corn planters Part I: Design and laboratory simulation. Comput. Electron. Agric. 144, 71–79 (2018).
Hensh, S. & Raheman, H. Laboratory evaluation of a solenoid-operated hill dropping seed metering mechanism for pre-germinated paddy seeds. J. Biosyst. Eng. https://doi.org/10.1007/s42853-021-00124-8 (2022).
Fengwei, G., Youqun, Z., Feng, W., Zhichao, H. & Lili, S. Simulation analysis and experimental validation of conveying device in uniform rrushed straw throwing and seed-sowing machines using CFD-DEM coupled approach. Comput. Electron. Agric. 193, 106720 (2022).
Shi, S. et al. Simulation and verification of seed-filling performance of pneumatic-combined holes maize precision seed-metering device based on EDEM. Trans. Chin. Soc. Agricultural Eng. 31, 62–69 (2015).
Li, Z., Yu, J., Zhang, W. & Fu, H. Simulation analysis of working process and performance of inside-filling seed metering device by discrete element method. Trans. Chin. Soc. Agricultural Eng. 27, 32–36 (2011).
Kun, Z. H. A. N. G. Y. I. Simulation and Experimental Optimization on Filling Seeds Performance of Seed Metering Device with Roller of Air-suction. Nongye Jixie Xuebao/Transactions Chin. Soc. Agricultural Machinery 48, (2017).
Shi, L. et al. Simulation test for metering process of horizontal disc precision metering device based on discrete element method. Trans. Chin. Soc. Agricultural Eng. 30, 40–48 (2014).
Lei, X. et al. Effects of seed layer thickness on seed filling performance of seed feeding device for rapeseed and wheat. Trans. Chin. Soc. Agricultural Eng. 32, 11–19 (2016).
Zhang, T. et al. Movement law of maize population in seed room of seed metering device based on discrete element method. Trans. Chin. Soc. Agricultural Eng. 32, 27–35 (2016).
Wang, Y. et al. Calibration method of contact characteristic parameters for corn seeds based on EDEM. Trans. Chin. Soc. Agricultural Eng. 32, 36–42 (2016).
Yu, Y. X., Yang, Y. Y., Zheng, B. & Zhang, F. Numerical simulation and experiment of motion of rice seed in pneumatic seed-metering device. Appl. Mech. Mater. 249, 657–662 (2013).
Gao, X. et al. DEM study of particle motion in novel high-speed seed metering device. Adv. Powder Technol. 32, 1438–1449 (2021).
Yu, Y., Fu, H. & Yu, J. DEM-based simulation of the corn threshing process. Adv. Powder Technol. 26, 1400–1409 (2015).
Deo, M. M., De, D., Mani, I. & Iquebal, M. A. Physical and engineering properties of urea briquettes relevant to design of mechanical applicator. Int. J. Chem. Stud. 7, 725–728 (2019).
Yasmeen, G. S., Ashraf, M., Yaseen, U., Ahmed, M. & Ahmed, S. Design, development and performance evaluation of manually operated garlic planter. J Glob Innov. Agric. Soc. Sci 6, (2018).
Pareek, C. M., Tewari, V. K., Machavaram, R. & Nare, B. Optimizing the seed-cell filling performance of an inclined plate seed metering device using integrated ANN-PSO approach. Artif. Intell. Agric. 5, 1–12 (2021).
Kepner, R. A., Bainer, R. & Barger, E. L. Principles of farm machinery. (1978).
Savant, N. K. & Stangel, P. J. Urea briquettes containing diammonium phosphate: A potential new NP fertilizer for transplanted rice. Nutr. Cycl. Agroecosyst. 51, 85–94 (1998).
Savant, N. K. & Stangel, P. J. Deep placement of urea supergranules in transplanted rice: Principles and practices. Fertil. Res. 25, 1–83 (1990).
Jianbo, Z., Junfang, X., Yong, Z. & Shun, Z. Design and experimental study of the control system for precision seed-metering device. Int. J. Agric. Biol. Eng. 7, 13–18 (2014).
Sun, J., Chen, H., Duan, J., Liu, Z. & Zhu, Q. Mechanical properties of the grooved-wheel drilling particles under multivariate interaction influenced based on 3D printing and EDEM simulation. Comput. Electron. Agric. 172, 105329 (2020).
Wang, J., Zou, D., Wang, J. & Zhou, W. Testing and analysis of the shear modulus of urea granules. in Computer and Computing Technologies in Agriculture VII: 7th IFIP WG 5.14 International Conference, CCTA Beijing, China, September 18–20, 2013, Revised Selected Papers, Part I 7 137–144 (Springer, 2014). (2013).
Wang, X. F. et al. Identification of mechanical parameters of urea-formaldehyde microcapsules using finite-element method. Compos. Part B Eng. 158, 249–258 (2019).
Muthe, L. P., Pickering, K. & Gauss, C. A review of 3D/4D printing of poly-lactic acid composites with bio-derived reinforcements. Compos. Part C Open Access 8, 100271 (2022).
Wang, M., Liu, Q., Ou, Y. & Zou, X. Numerical simulation and verification of seed-filling performance of single-bud billet sugarcane seed-metering device based on EDEM. Agriculture 12, 983 (2022).
Reddy, B. S., Adake, R. V. & Anantachar, M. Performance of seed planter metering mechanisms under simulated conditions. Indian J. Dryland Agric. Res. Dev. 27, 36–42 (2012).
Chhinnan, M. S., Young, J. H. & Rohrbach, R. P. Accuracy of seed spacing in peanut planting. Trans. ASAE 18, 828–831 (1975).
Sharma, V. K., Sharma, D. N. & Kumar, D. Development and evaluation of tractor drawn inclined cell plate type Bt cotton planter. Int. J. Agric. Eng. 6, 329–334 (2013).
Wang, H. et al. Design and parameter optimization of a finger clip plate garlic seed-metering device based on EDEM. Agronomy https://doi.org/10.3390/agronomy12071543 (2022).
Bagherpour, H. Modeling and Evaluation of a Vacuum-Cylinder Precision Seeder for Chickpea Seeds. vol. 21 (2019). http://www.cigrjournal.org
Mandal, S., Kumar, G. V. P., Tanna, H. & Kumar, A. Design and evaluation of a pneumatic metering mechanism for power tiller operated precision planter. Curr. Sci. 115, 1106–1114 (2018).
Asl, A. R., Roudbari, M. & Esmailzadeh, E. Fabrication and evaluation of vacuumed metering drum performance for row planting of soybean with grease belt. Agric. Eng. Int. CIGR J. 21, 96–106 (2019).
Acknowledgements
The authors extend their appreciation to Ongoing Research Funding program – Research Chairs (ORF-RC-2025-5527), King Saud University, Riyadh, Saudi Arabia.
Funding
Open access funding provided by University of Pécs. This research was funded by Ongoing Research Funding program – Research Chairs (ORF-RC-2025-5527), King Saud University, Riyadh, Saudi Arabia.
Author information
Authors and Affiliations
Contributions
S.S.S., T.K.K., P.A., M.A.M. and H.L.K: Conceptualization, Methodology, Formal analysis, Software, Writing- Original draft preparation. S.S.S., R.A.P., D.S., P.K.S., P.M., K.B., N.A.-A. and A.S.: Supervision, Comments and Revisions Recommendations, Writing- Reviewing and Editing. All authors have read and agreed to the published version of the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and permissions
About this article
Cite this article
Swain, S.S., Khura, T.K., Arjun, P. et al. Modelling and optimization of operating parameters of an electronic cell type metering mechanism for urea super granules (USG) using EDEM-RSM approach.
Sci Rep (2026). https://doi.org/10.1038/s41598-026-43407-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-026-43407-w
Keywords
- EDEM
- RSM
- USG
- Simulation
- Optimization
Source: Ecology - nature.com
